Interest in both the time effect on the timber mechanical properties and the reuse of old solid timbers has prompted many research works since the 1970s, mainly focusing on evaluating bending strength (MOR) and stiffness (MOE). However, only few studies have investigated the effect of aging on shear modulus (G). In this work, transverse vibration test is used to calculate G and MOE of over 80 old timber beams. The MOE/G ratio and the relationship between G and different timber features are investigated. The main outcome of the research confirms that the MOE/G ratio is around 20, close to the value reported in literature for new solid timber. No relationship exists between G and MOE (r2=0.07) or between G and other timber features. When density and knots are used as predictors in a multiple regression model, the G prediction improves (r2=0.22). This work confirms that G is not affected by the age of timber.
Flexural VibrationOld TimberHistorical Timber BuildingsReclaimed TimberWood Technology and Forest HarvestingIntroduction
The interest in recycling old timber has increased recently (Kránitz et al. 2013). Salvaged timbers can be reused for making furniture, interior design and restoration works. Brandon Davis (2012) presented a detailed and thorough review of benefits and opportunities of using reclaimed wood. To reuse reclaimed timber in wood construction, the mechanical properties must be taken into consideration. Many research works have investigated the aging effects on the bending Modulus of Elasticity (MOE) or the bending strength (MOR) of old timber, since the MOE is well related to the overall quality of timber and MOR is usually the most important and limiting factor in timber structures. In some cases, the mechanical properties of wood were not being significantly affected by aging process if the wood is preserved by decay phenomena (Kuipers 1986, Ehlbeck & Görlacher 1990, Rug & Seemann 1991, Togni 1995, Yokoyama et al. 2009, Kránitz et al. 2013). Other works reported a significant bending strength reduction (Attar-Hassan 1976, Piao et al. 2004, Nakajima 2008). This explains why the effect of aging on the mechanical properties of old timber is still of interest for architects and structural engineers.
Shear modulus (G) is the ratio of shear stress to shear strain, describing the material’s response to shear stress. It is a basic property of materials, essential for the efficiency of construction procedures (Yoshihara 2011) when short members are considered within a structure or for parts subjected to torsion action and when timber is loaded in bending, because in nearly all cases, deflection is also affected by G. It is also used by structural engineers for finite element analysis and for various strengthening intervention designs such as beams ends prosthesis. Finally, the MOE/G ratio is used in design equations to determine torsional rigidity and to predict structural beams’ lateral torsional stability.
Shear modulus is usually assumed as a portion of MOE, because in clear wood both are related to the density and the microfibril angle within the cell walls. For structural timber, G is also affected by many other features such as slope of grain, knots and presence of pith.
The determination of G by mechanical tests is quite difficult, it is biased by errors and it is time-consuming (Brandner et al. 2007), so many researchers used dynamic methods applied to small specimens. Chui (1991) calculated the G values comparing clear and unclear small specimens obtained from the same boards to evaluate the effect of knots on both MOE and G. Divos et al. (1998) investigated the relationship between statically and dynamically determined G on small specimens. Carreira (2012) used transverse vibration test to calculate the MOE/G ratio of 20 full dimension logs (2.25 m long, 16 cm diameter). Kránitz et al. (2013) and Noguchi et al. (2011) investigated the G value of small clear specimens obtained from old timber beams, demonstrating that G is not affected by age. Recently, Olsson & Källsner (2015) used the transverse vibration test to evaluate both MOE and G and their relationship on Norway spruce boards, reporting that G largely depends on density and is poorly correlated to the MOE. The goals of this research are to calculate the shear modulus of structural timber coming from different historical buildings, to investigate the relationship between G, timber features (density, knots, slope of grain, ring shake) and MOE, and to compare them to the values reported in the literature for new structural timber.
Materials and methodsMaterials
Eighty-four structural timber beams were tested and carefully inspected. Seventeen were spruce (Picea abies Karst.), and 67 were silver fir (Abies alba Mill.). Since the two species have similar physical and mechanical properties, they were considered together in this work, as many visual grading rules state for new timber. Based on the historical research, all the beams are older than 70 years, so it is possible to suppose that they were not subjected to high stress levels during their service life, according to the effect of the duration of load (Hoffmeyer & Sørensen 2007). In the original buildings, the beams were mainly used as part of trusses (rafters and tie beams) and floor beams, and consequently were subjected to different stress actions (bending, compression and tension).
The average cross-section of the beams was between 14×14 and 28×22 cm2, and the average length was about 470 cm.
Different timber features affecting the mechanical properties of wood were observed and recorded.
Slope of grain: calculated as the angle between the fibre orientation and the longitudinal axis of the timber. It is an important factor affecting the elastic properties of wood.
Knots: they affect both MOE and G. In this work, knots were evaluated according to the visual strength grading rules of solid timber UNI-11119 (2004) and UNI-11035-1/2 (2010), as the ratio between the minimum diameter of a knot and the dimension of the face on which it appears, and recording the maximum observed value.
Wane: their dimensions were measured, and the ratio between the cathetus and the length of its corresponding face was calculated. Wane are quite common in old structural timber of large dimension, though it is well known that they do not reduce the mechanical properties of timber (Togni et al. 2013).
Ring shake: it is a discontinuity between two consecutive annual rings that reduces the cross-section and affects shear strength and modulus. In this work, it was calculated according to UNI-11035-1/2 (2010), by measuring the distance between the pith and the ring shake.
Decay and insect damages: presence and extension of decay and insects attacks were observed and recorded to identify the real cross-section of each timber.
Other damages: since it is quite common to observe damages (like holes) in old timber caused by mounting and dismounting operations, all of them were recorded.
Checks: since the pith was always included in the tested beams, checks appear as a consequence of the drying process. Their extensions in the longitudinal and transverse directions were measured.
Density: directly related to mechanical properties and used for G calculation. All the beams were measured and weighed to calculate density as the mass to volume ratio (volume calculated by multiplying the length for the average cross-section measured at the ends and at 1/3 and 2/3 of the length).
Moisture content (MC): it was calculated using gravimetric method on clear specimens after testing timber at failure. Tab. 1 reports the MC range and variation. In softwood species, MOE and G vary linearly by about 1.5% and 2.2%, respectively, every 1% MC below the fibre saturation point (Wilson 1932). Therefore, no correction was applied to MOE or G. The quality of the tested beams was strongly variable, as when they were used, no standardized selection was made based on quality. Thus, the sample contains beams of good quality (high density, small knots, no slope of grain) as well as beams of poor quality (large knots and high slope of grain, mainly) that are not suitable for structural uses based on modern grading rules.
The timber beams showed different conservation status. Only 24 were affected by decay, for all of them the position and extension of decay were recorded. According to Gilfillan & Gilbert (2001) and Cruz & Machado (2013), the effect of insect attack was negligible. In this work, none of the tested beams was affected by severe attacks, and the attacks were limited to the sapwood, as determined by visual inspection. Therefore, both research works demonstrated that for the investigated species strength does not decrease considerably, even when the level of the attack is high.
Only 12 timbers presented ring shakes of various extensions. Ring shake and checks affect not only mechanical properties, but also the mode of vibration in dynamic tests. When the extension of such defects is too large, the timber beams response in flexural vibration is biased, the frequencies of vibration change, the results do not converge and those beams were excluded from the analysis (see below).
Dynamic tests
Dynamic methods have been used in several studies to evaluate G and for the simultaneous evaluation of G and MOE (Chui 1991, Divos et al. 1998, Larsson et al. 1998, Khokhar 2011, Carreira 2012, Kránitz et al. 2013, Olsson & Källsner 2015). Those methods combine the reliability of the results with the simplicity and rapidity required to carry out the tests. Vibration test is a simple and efficient way to characterise the elastic properties of timber; in fact, it has been used since the ’80s for assessing timber quality.
Transverse vibration tests are based on the resolution of the motion equations of flexural vibrations. Different authors have proposed various theoretical models and solutions characterised by specific validity ranges and accuracy levels (Brancheriau & Bailleres 2002). In 1921, Timoshenko proposed the differential equation for motion. Different solutions were lately proposed by Goens (1931), Rayleigh (1945) and Bordonné (1989).
Frequency equations allow calculation of both G and MOE. Chui (1991) proposed a method for the calculation of MOE and G based on the first two vibration frequencies. An alternative method to calculate G based on the same vibration test was proposed by Kubojima et al. (1996). In this work, the Bordonne’s solution to Timoshenko’s model was adopted for the simultaneous calculation of G and MOE. The same method has already been used by other authors to calculate G and MOE (Roohnia et al. 2010, Roohnia et al. 2012, Yavari et al. 2013). This solution can be applied only when the length to depth ratio of the beam is higher than 10 (the minimum ratio of the tested beam is 15), which is applicable in this case. This solution considers the first 3 to 5 vibration frequencies of each beam. For each beam, the equation system is solved, and a pair of coordinates (xn, yn) are computed. The coordinates are reported in a Cartesian coordinate system and fitted with a trend line (Fig. 1), where the intercept represents the specific MOE (MOE/ρ) and the slope corresponds to the MOE to G ratio. In our case, four frequencies were considered and four couple of coordinates computed using the following equation (eqn. 1):
y = {\frac{ MOE} { \rho }} - {\frac{ MOE} { kG}} \cdot x
where ρ is the density, k is the Timoshenko’s shear correction factor (0.83 for rectangular and squared section), G the shear modulus in vibration plane and MOE the dynamic Modulus of Elasticity.
Only the regression curves with a coefficient of determination (r2) higher than 0.9 were used, as lower r2 indicates biased mode of vibration; therefore, only 81 beams were considered in the study. The excluded beams presented too much extended and deep checks or ring shakes or higher deformation.
All the beams were suspended by two threads at their theoretical nodes (points of zero vibration) and tested in free-free flexural vibration (Fig. 2). Transverse vibration was induced by striking the beams using a hammer in the direction of the depth. A piezoelectric accelerometer (PCB 480E09®, PCB Piezotronics Inc., Depew, NY, USA) was placed on the opposite part of the beam to acquire the mode of vibration. The signal was processed by Fast Fourier Transform (FFT), and the resonant frequencies were identified using a LabVIEW® software application (National Instruments Corp., Austin, TX, USA). In this paper, only the results concerning G and MOE/G calculated using a dynamic technique are reported and discussed.
Results and discussion
Tab. 1 shows the average values of the main physical and mechanical properties. The average G was approximately 400 MPa; it has to be stressed that more than 50% of the beams had G value higher than 350 MPa (Fig. 3). Variability was quite high (CV=28%) as a consequence of the high variability of the material itself. CV was around 30% for both G and MOE. The mean MOE/G for the tested material was 21 (minimum 7, maximum 36).
Due to the characteristics of the tested materials (structural timber of various quality and state of conservation), it is quite difficult to compare G to the results reported in literature because it is usually obtained with very different conditions (new material, small clear specimens, small unclear specimens, static tests, dynamic tests, etc.). In this case, it is much more suitable to compare the MOE/G ratio obtained in different research works based on the application of dynamic tests (Tab. 2).
Kránitz et al. (2013) and Noguchi et al. (2011) stated that aging has no significant effects on MOE/G. Both works tested small clear specimens of old wood oriented along a longitudinal-radial direction (Noguchi et al. 2011) and in longitudinal-radial/longitudinal-tangential direction (Kránitz et al. 2013). The authors reported significantly different MOE/G (27 and 8, respectively). This difference is a consequence of the different dimensions and orientations of the tested specimens and also of the different dynamic techniques used. These values are also different from the MOE/G calculated within this study for several reasons. In structural timber, defects affect both G and MOE, and structural timbers are usually not oriented along the main anatomical directions, but rather a mix of longitudinal-radial and longitudinal-tangential directions, which justifies the larger variability of the results.
Studies focused on materials with defects report a MOE/G ratio closer to the outcomes reported in this investigation. Chui (1991), tested a mixed sample of clear and unclear small specimens, reporting a MOE/ G = 23. Carreira (2012) tested logs of dimension closer to the materials used in this research and reports an average MOE/G = 19. The MOE/G obtained here shows higher variability compared to the Carreira’s results as a consequence of the characteristics of the material itself. This author tested highly homogeneous material (CV lower than 10% for all mechanical properties) by exciting it in the same anatomical direction. Olsson & Källsner (2015) reported a MOE/G in the range of 15-17 for Norway spruce lumbers.
These results confirm that MOE and G are affected by defects in different ways, as previously reported by Chui (1991) and Gupta et al. (2004). The effect of knots on G is related to their number, position and orientation, as reported by Gupta et al. (2004) and Olsson & Källsner (2015). The importance of knots seems to be confirmed in this study, since the relationship between knots and G showed the higher correlation value between G and all the timber features (r2 = 0.11, p < 0.01), and the knots were evaluated according to two visual grading rules (UNI-11119 2004, UNI-11035-1/2 2010) that considered only the largest one in a beam, without taking into account their number, position and orientation. Knots and MOE did not show any significant correlation (r2 = 0.003, p>0.05), confirming that the MOE is not influenced by local defects. Thus, knots seem to have a greater effect on G than on MOE, suggesting that using G to improve the bending strength prediction could be valid also for old timber, as proposed by Olsson & Källsner (2015).
No relationship was found between G and other timber features such as density, slope of the grain, presence and extension of ring shakes and wane. Additionally, MOE and G did not show significant relationships (r2 = 0.07, p>0.05 - Fig. 4), as already reported in the literature (Chui 1991, Olsson & Källsner 2015).
An improvement in the G prediction is possible using knots and density as predictors in a multiple linear regression (r2= 0.2, p<0.01 - Fig. 5). This is because, according to many authors (Chui 1991, Gupta et al. 2004, Olsson & Källsner 2015), the driving factors for G are density and knots. The multiple regression analysis confirmed the results reported by Olsson & Källsner (2015), who used MOE and density as regressors to predict G (r2= 0.39). Indeed, they found that MOE was correlated to the presence of important defects like the quantity of knots and the slope of grain that have important effects in increasing G. The lower accuracy in predicting G obtained in this study is likely due to the larger variability of the old timber analyzed, as compared with the new materials tested by Olsson & Källsner (2015).
Conclusions
Eighty-four old timber beams were dynamically tested by means of free-free flexural vibration test. Applying the Bordonné solution, both G and MOE were calculated simultaneously.
The mean G for the whole sample was of about 400 MPa, and the average MOE/G was around 21, close to the value reported in different papers for unclear specimens and for new structural timber.
No relationships were found between G and MOE (r2 = 0.07) or between G and other timber features (slope of grain, density, etc.). The relationship between G and knots, though limited (r2 = 0.11), seems to confirm the results previously reported in the literature. This suggests an important effect of knots, their dimensions and orientations on the G values that requires further in-depth investigation. These results are consistent with those reported in the literature both for new structural timbers and unclear specimens, confirming also that G, like other mechanical properties of wood, is not significantly affected by aging.
ReferencesAttar-Hassan GThe effect of ageing on the mechanical properties of eastern white pine. Association for Preservation Technology (APT) 8: 64-73.1976Bordonné PModule dynamique et frottement intérieur dans le bois: mesures sur poutres flottantes en vibrations naturelles. [Dynamic modulus and internal friction in clear wood: measurement by means of of free-free flexural vibrations]. Thèse de doctorat en Sciences du Bois, INPL, Vandoeuvre-les-Nancy, France, pp. 154. [in French]1989Brancheriau L, Bailleres HNatural vibration analysis of clear wooden beams: a theoretical review. Wood Science and Technology 36: 347-345.2002Brandner R, Gehri E, Bogensperger T, Schickhofer GDetermination of modulus of shear and elasticity of glued laminated timber and related examinations. CIB W18 40-12-12, Conseil International dû Batiment, Esres Park, CO, USA, pp. 227.2007Brandon Davis JSuitability of salvaged timber in structural design. Master Thesys, Massachusetts Institute of Technology, Civil and Environmental Engineering, United States Military Academia, Boston, MS, USA, pp. 42. -2012Carreira MRDetermination of the E/G ratio of wood logs using transversal vibration. Wood Research 57 (2): 207-220.2012Chui YHSimultaneous evaluation of bending and shear moduli of wood and the influence of knots on these parameters. Wood Science and Technology 25: 125-134.1991Cruz H, Machado JSEffects of beetle attack on the bending and compression strength properties of pine wood. Advanced Materials Research 778: 145-151.2013Divos F, Tanaka T, Nagao H, Kato HDetermination of shear modulus on construction size timber. Wood Science and Technology 32: 393-402.1998Ehlbeck J, Görlacher RDie Tragfähigkeit von altem Konstruktionsholz - Problematik der Beurteilung. [Assessment of old timber buildings strength]. Bauen mit Holz 2 (90): 117-120. [in German]1990Gilfillan JR, Gilbert SGDevelopment of a technique to measure the residual strength of woodworm infested timber. Construction and Building Materials 15: 381-388.2001Goens EBer die Bestimmung des Elastizitätsmoduls von Stäben mit Hilfe von Biegungsschwingungen [Determination of Young’s modulus from flexural vibrations]. Annalen Der Physik 7 (11): 649-678. [in German]1931Gupta R, Basta C, Kent SMEffect of knots on longitudinal shear strenth of douglas-fir using shear blocks. Forest Product Journal 54 (11): 77-83.2004Hoffmeyer P, Sørensen JDDuration of load revisited. Wood Science and Technology 41 (8): 687-711.2007Khokhar AThe evaluation of shear properties of timber beam using torsion test method. Doctoral Thesys, Centre for Timber Engineering School of Engineering and the Built Environment, Napier University, Edinburgh, Scotland, UK, pp. 178.2011Kránitz K, Deublein M, Niemz PDetermination of dynamic elastic moduli and shear moduli of aged wood by means of ultrasonic devices. Materials and Structures 47 (6): 925-936.2013Kubojima Y, Yoshihara H, Ohta M, Okano TExamination of the method of measuring the shear modulus of wood based on the Timoshenko theory of bending. Mokuzai Gakkaishi 42: 1170-1176.1996Kuipers JEffect of age and/or load on timber strength. In: Proceedings of the Meeting “CIB W18”. Florence (Italy) 20 Sept 1986, vol I, paper no. 19-6-1, pp. 156-189.1986Larsson D, Ohlsson S, Perstorper M, Brundin JMechanical properties of sawn timber from Norway spruce. Holz als Roh- und Werkstoff 56 (5): 331-338.1998Nakajima SComparison of two structural reuse options of two-by-four salvaged lumbers. In: Proceedings of the “WCTE 2010 - World Conference on Timber Engineering”. Riva del Garda (Italy) 20-24 Jun 2010. Trees and Timber Institute, National Research Council, Trento, Italy, vol. 4, pp. 1085-1090.2008Noguchi T, Obataya E, Ando KEffects of ageing on the vibrational properties of akamatsu (Pinus densiflora) wood. Wood Culture and Science, Kyoto, Japan, pp. 112-118.2011Olsson A, Källsner BShear modulus of structural timber evaluated by means of dynamic excitation and FE analysis. Materials and Structures 48: 977-985.2015Piao C, Shupe TF, Hse CY, Tang RCNondestructive evaluation of Young’s moduli of full-size wood laminated composite poles. In: Proceedings of the “7th Pacific Rim Bio-Based Composites Symposium”. Najing (China) 31 Oct - 2 Nov 2004. Science and Technique Literature Press, Nanjing, China, vol. 2, pp. 291-298.2004Rayleigh LTheory of sound. Vol. 1 (2nd edn). Dover Press, New York, USA, pp. 370.1945Roohnia M, Kohantorabi M, Jahan-Latibari A, Tajdini A, Ghaznavi MNondestructive assessment of glued joints in timber applying vibration-based methods. European Journal of Wood and Wood Products 70 (6): 791-799.2012Roohnia M, Yavari A, Tajdini AElastic parameters of poplar wood with end-cracks. Annals of Forest Science 67 (4): 1-6.2010Rug W, Seemann AStrength of old timber. Building Research and Information 19: 31-37.1991Togni M, Cavalli A, Mannozzi DChestnut: from coppice to structural timber. The case study of “Uso Fiume” beams sampled in Liguria. Journal of Agricultural Engineering 44(9): 1-4.2013Togni MElasticità e resistenza di travi lignee antiche di grandi dimensioni: stima con metodologie non distruttive di prova applicabili in opera [Stiffness and Strength of old structural timber beams: on-site assessment by means of NDT techniques]. Doctoral Thesys, University of Florence, Italy, pp. 89. [in Italian]1995UNI-11119Cultural heritage - Wooden artefacts - Load bearing structures of buildings - On site inspection for the diagnosis of timber members. Italian Unification Body, Milan, Italy, pp. 9.2004UNI-11035-1/2Structural timber. Visual strength grading for structural timbers. Italian Unification Body, Milan, Italy, pp. 35.2010Wilson TRCStrength-moisture relations for wood. Technical Bulletin no. 282, USDA, Washington, DC, USA, pp. 89.1932Yavari A, Roohnia M, Tajdini AMechanical properties of clear poplar wood vs. cracked and drilled bars. In: Proceedings of the “18th International Nondestructive Testing and Evaluation of Wood Symposium”. Madison (WI, USA) 24-27 Sept 2013. USDA, Washington, DC, USA, pp. 677-684.2013Yokoyama M, Gril J, Matsuo M, Yano H, Sugiyama J, Clair B, Kubodera SMechanical characteristics of aged Hinoki wood from Japanese historical buildings. Comptes Rendus Physique 10 (7): 601-611.2009Yoshihara HExamination of the edgewise shear modulus of wood measured by dynamic square-plate. Wood Research 56 (3): 311-320.2011
Fitted trend line using the first four vibration frequencies.
Transverse vibration test layout.
Shear modulus (G) frequency distribution.
Relationship between modulus of elasticity (MOE) and shear modulus (G). 0.07 > p-value > 0.01.
Shear modulus (G) prediction using knots (k) and density (d) (knots considered according to the standard - UNI-11035-1/2 2010). p-value < 0.01.
Descriptive statistics for density (ρ), Modulus of Elasticity (MOE), shear modulus (G) and MOE/G ratio of the tested timber beams. (MC): moisture content.